Defensive TurfStat Pro Sanitizer
TurfStat Pro™ is a Hospital-Grade liquid Disinfectant, Sanitizer, Fungicide, Virucide, and Mildewstat. Diluted in water and applied to synthetic turf fields using a boom-type sprayer attached to a motorized vehicle or a pressurized pump system. Can also be spot applied with a hand-held pump sprayer.
TurfStat Pro™ is proven to kill germs on non-porous surfaces such as plastic (polystyrene, polypropylene, …), vinyl, fiberglass, non-porous rubber, and washable synthetic fibers. Compatible with materials used in the manufacture and installation of artificial athletic turf and surfaces.
No rinsing is required.
** Please see full efficacy
Outdoor application – apply only if rain is not expected for at least 8 hours.
Do not apply in windy conditions.
** Allow playing field to dry entirely prior to use (2-hour minimum recommended)
This product may be used on washable, hard, non-porous surfaces such as: vinyl, plastic, polystyrene and polypropylene.
This product is a concentrated disinfectant that is effective against a broad spectrum of bacteria, is Virucidal*, fungicidal, and eliminates odor-causing bacteria when used as directed. This product may be applied through low-pressure sprayers.
It is a violation of Federal Law to use this product in a manner inconsistent with its labeling.
Apply this product with a mechanical spray device. When applied with a mechanical spray device, surfaces must be sprayed until thoroughly wetted. Treated surfaces must remain wet for 10 minutes. For sprayer applications, use a coarse pump or trigger sprayer. Spray 6-8 inches from surface. Rub with brush, sponge or cloth. Do not breathe spray. NOTE: With spray applications, cover or remove all food products. Prepare a fresh solution at least daily or when use solution becomes visibly dirty. For heavily soiled areas, a preliminary cleaning is required.
To disinfect hard, inanimate surfaces, add 4 oz. TurfStat PRO™ per gallon of water. Apply solution with mechanical sprayer so as to wet all surfaces thoroughly. Allow treated surfaces to remain wet for 10 minutes and then let air dry. For sprayer applications, use a coarse spray device. Spray 6-8 inches from surface. Rub with brush, sponge or cloth. Do not breathe spray. For heavily soiled areas, a pre-cleaning step is required. Prepare a fresh solution at least daily or when use dilution becomes diluted or soiled.
Fungicidal Activity: At 4 ounces per gallon use-level, (or equivalent use dilution) (488 ppm active quat) this product is effective against Trichophyton mentagrophytes (athlete’s foot fungus) (a cause of Ringworm) on inanimate surfaces in locker rooms, dressing rooms, shower and bath areas and exercise facilities. Pre-clean all surfaces prior to using this product.
DISINFECTION/FUNGICIDAL ACTIVITY: At 4 oz per gallon dilution, with a 10-minute contact time, this product exhibits effective disinfectant activity against the following: Brevibacterium
ammonia genes ATCC# 6872 • Enterococcus faecalis (Vancomycin resistant) – VRE (ATCC# 51299) • Escherichia coli ATCC# 11229 • Klebsiella pneumonia ATCC# 4352 • Proteus mirabilis ATCC# 9240 • Pseudomonas aeruginosa PRD-10 ATCC# 15442 • Staphylococcus aureus (MRSA) (Methicillin resistant) ATCC# 33592 • Staphylococcus aureus (Vancomycin resistant) – VISA (HIP 5836) • Streptococcus faecalis
FUNGICIDAL PERFORMANCE: Aspergillus niger ATCC# 6275 • Trichophyton mentagrophytes (Athletes’ foot fungus) ATCC# 9533
VIRUCIDAL* ACTIVITY: The product when used on environmental inanimate hard surfaces at 4 oz per gallon of water exhibits effective virucidal* activity against: Adenovirus Type 2 (causative agent of upper respiratory infections) • Herpes simplex, Type 1 • Herpes simplex, Type 2 • Human Coronavirus •Influenza A2 /Japan (representative of the common flu virus) • Vaccinia Virus (representative of the pox virus group).
CLEANING AND DISINFECTION: For all general cleaning and disinfection use 4 ounces of this product per gallon of water (or equivalent use dilution) (488 ppm active quat). Apply this to remain wet for 10 minutes and then let air dry. For heavily soiled areas, a pre-cleaning step is required. Prepare a fresh solution after each use. For sprayer applications, use a coarse spray device.
SANITIZER DIRECTIONS (for non-food contact surfaces)
Preparation of sanitizer use solution: Add 6 ounces of this product to 1 gallon of water (732 ppm active) to sanitize hard, non-porous surfaces. At 732 ppm active, this product is an effective one-step sanitizer against Staphylococcus aureus and Klebsiella pneumonia. Apply sanitizer use solution to pre-cleaned, hard non-porous surfaces with sprayer. For sprayer applications, use a coarse pump or trigger sprayer. Spray 6-8 inches from surface and rub with brush, sponge or cloth. Do not breathe spray. Treated surfaces must remain wet for 60 seconds, then wipe with sponge, mop or cloth or allow to air dry.
Subscribe today and get 10% off your first purchase